钢轨轨面静电喷涂SiO_2增黏颗粒行为与利用率研究_黄启芮.pdf
《钢轨轨面静电喷涂SiO_2增黏颗粒行为与利用率研究_黄启芮.pdf》由会员分享,可在线阅读,更多相关《钢轨轨面静电喷涂SiO_2增黏颗粒行为与利用率研究_黄启芮.pdf(12页珍藏版)》请在咨信网上搜索。
1、 表面技术 第 52 卷 第 6 期 196 SURFACE TECHNOLOGY 2023 年 6 月 收稿日期:20220516;修订日期:20220908 Received:2022-05-16;Revised:2022-09-08 基金项目:国家重点研发计划政府间国际科技创新合作重点专项(2018YFE0109400);四川省苗子工程项目(2021JDRC0086);中国国家铁路集团有限公司科技研究开发计划系统性重大项目(P2021J038)Fund:National Key R&D Program Intergovernmental Key Items for Internation
2、al Scientific and Technological Innovation Cooperation(2018YFE0109400);Sichuan Science and Technology Program(2021JDRC0086);Systematic Major Project of Science and Technology Research and Development Plan of China State Railway Group Co.,Ltd.(P2021J038)作者简介:黄启芮(1998),男,硕士生,主要研究方向为轮轨增黏调控技术。Biography:
3、HUANG Qi-rui(1998-),Male,Postgraduate,Research focus:wheel/rail adhesion control technology.通讯作者:丁昊昊(1988),男,博士,助理研究员,主要研究方向为轮轨摩擦学。Corresponding author:DING Hao-hao(1988-),Male,Doctor,Research assistant,Research focus:tribology of wheel and rail.引文格式:黄启芮,张沭玥,王文健,等.钢轨轨面静电喷涂 SiO2增黏颗粒行为与利用率研究J.表面技术,202
4、3,52(6):196-207.HUANG Qi-rui,ZHANG Shu-yue,WANG Wen-jian,et al.Behaviour and Utilization Rate of SiO2 Particles by Electrostatic Spraying on Rail SurfaceJ.Surface Technology,2023,52(6):196-207.钢轨轨面静电喷涂 SiO2增黏颗粒 行为与利用率研究 黄启芮1,张沭玥2,王文健1,2,师陆冰3,林强2,丁昊昊1,2(1.西南交通大学 唐山研究院,河北 唐山 063000;2.西南交通大学 机械工程学院,成都
5、610031;3.郑州机械研究所有限公司,郑州 450052)摘要:目的目的 为了改善传统撒砂过程中 SiO2增黏微粒利用率低的问题,将静电喷涂技术引入轮轨增黏领域,研究不同喷涂参数与颗粒粒径对 SiO2微粒行为与利用率的影响,并进一步对比分析静电喷涂微粒与传统撒砂的增黏效果。方法方法 利用 Gema 静电喷枪与静电喷涂动态试验平台进行喷涂试验;利用MJP30A 轮轨滚动磨损与接触疲劳试验机进行轮轨黏着与磨损试验;利用光学显微镜(OM)对 SiO2微粒吸附情况进行观察与分析,并通过电子天平测量与计算轨面颗粒量与颗粒利用率。结果结果 相较于未施加静电电压,静电电压为 90 kV 时轨面颗粒量提升
6、了 3.8 倍。静电电压由 30 kV 增加至 70 kV 时,颗粒利用率提升约 60%;当静电电压进一步增加至 90 kV 时,由于颗粒带电量趋于饱和,颗粒利用率仅提升 10%。SiO2微粒利用率随着喷嘴高度与颗粒粒径的增大先增大后减小,喷嘴高度为 25 cm 且颗粒粒径为 300 目时颗粒利用率最高,可达 60%;300 目 SiO2微粒在静电电压为 90 kV 时,随着喷枪移速的增大,喷枪在单位距离上喷涂时间相对减少,使得喷涂在钢轨轨面的颗粒量降低。90 kV 静电喷涂SiO2微粒增黏时,最大黏着系数接近传统撒砂增黏,有效作用时间是传统撒砂的 2.2 倍,轮轨磨损率仅为传统撒砂增黏的 7
7、5%与 65%,轮轨损伤显著减轻。结论结论 利用静电喷涂技术可以有效提升 SiO2微粒在钢轨轨面的利用率,并提升颗粒在轨面的吸附性;静电喷涂 SiO2微粒增黏与传统撒砂增黏的黏着系数相近,且轮轨磨损率更低。关键词:静电喷涂;轮轨增黏;撒砂增黏;增黏颗粒;颗粒参数 中图分类号:TH117.3 文献标识码:A 文章编号:1001-3660(2023)06-0196-12 DOI:10.16490/ki.issn.1001-3660.2023.06.017 Behaviour and Utilization Rate of SiO2 Particles by Electrostatic Sprayi
8、ng on Rail Surface HUANG Qi-rui1,ZHANG Shu-yue2,WANG Wen-jian1,2,SHI Lu-bing3,LIN Qiang2,DING Hao-hao1,2 摩擦磨损与润滑 第 52 卷 第 6 期 黄启芮,等:钢轨轨面静电喷涂 SiO2增黏颗粒行为与利用率研究 197 (1.Tangshan Institute,Southwest Jiaotong University,Hebei Tangshan 063000,China;2.School of Mechanical Engineering,Southwest Jiaotong Univ
9、ersity,Chengdu 610031,China;3.Zhengzhou Research Institute of Mechanical Engineering Co.,Ltd.,Zhengzhou 450052,China)ABSTRACT:In railway systems,sands are often applied to the wheel-rail interface to improve the adhesion coefficient.However,hard particles such as quartz sand will inevitably cause we
10、ar to the wheel and rail after entering the contact area of wheel and rail.The viscosity increase effect of sand sprinkling mainly comes from the broken sand particles and has nothing to do with particle size.Therefore,using SiO2 particles instead of sand particles to increase viscosity can not only
11、 meet the viscosity increase effect but also significantly reduce wheel-rail damage.However,due to the small particle size and lightweight of SiO2 particles,it is difficult to effectively apply SiO2 particles to the wheel-rail interface by using the sand spout device in the current railway system.If
12、 electrostatic spraying is used to improve the utilization rate of SiO2 particles,it will have a high application prospect.Therefore,the work aims to introduce electrostatic spraying technology into the wheel-rail viscosity increase field and study the effects of different spraying parameters and pa
13、rticle sizes on the behavior and utilization of SiO2 particles,so as to solve the problem of low utilization of SiO2 viscosity increase particles in the traditional sanding process,and further compare and analyze the viscosity increase effects of electrostatic spraying particles and traditional sand
14、ing.The rail material selected in the test was U75V rail cut at each section of 50 cm from the site,and the size of SiO2 micro-powder was 100,200,300 and 500 mesh,and the content of silica in SiO2 micro-powder was more than 95%.Before each coating test,the rail surface was sanded,polished and cleane
15、d with anhydrous ethanol and the spray gun was flushed with compressed air to prevent powder from blocking the muzzle,and the grounding wire was fixed to the rail.During the test,the Gema electrostatic spray gun was fixed on the rodless slider of the dynamic test bench.At the end of the coating test
16、,it stood for 5 min,and after the suspended particles in the air were completely deposited,the particles adsorbed on the rail surface were collected and weighed by an electronic balance,and then the effective utilization rate was calculated,and the particle adsorption was observed by an optical micr
17、oscope.Compared with the traditional spraying method,the amount of SiO2 particles on the rail surface by electrostatic spraying increased about 3.8 times.When the electrostatic voltage was increased from 30 kV to 70 kV,the particle utilization rate increased by 60%,but when the electrostatic voltage
18、 was further increased to 90 kV,since the particle charge tended to saturate,the particle utilization rate only increased by 10%.The utilization rate of SiO2 particles firstly increased and then decreased with the increase of nozzle height and particle size.When the nozzle height was 25 cm and the p
19、article size was 300 mesh,the particle utilization rate was the highest,reaching 60%.When the electrostatic voltage of the 300 mesh SiO2 particles was 90 kV,the spraying time of the spray gun on the unit distance was relatively shortened with the increase of the moving speed of the spray gun.Therefo
20、re,the number of spraying particles on the rail surface of the spray gun decreased with the increase of the speed.When the nozzle height was 10 and 25 cm,the particle utilization rate increased with the increase of flow rate.When the nozzle height was 35 cm,the particle utilization rate increased fi
21、rstly and then decreased with the increase of the gun moving speed.Compared with the nozzle of 1 m/s,the particle utilization rate of 9 m/s nozzle height at 10 and 25 cm increased by 8%and 7%respectively,while the particle utilization rate at 35 cm decreased by 8%.When 2 g viscous particles were spr
22、ayed on a single time,the adhesion enhancement effect of direct spraying SiO2 particles was lower than traditional sand spraying and electrostatic spraying.At electrostatic voltage of 90 kV,the maximum adhesion coefficient of SiO2 particles by electrostatic spraying was close to traditional sand spr
23、aying,and the action revolution was 400 revolutions,which was 8 times of that under direct spraying SiO2 particles and 2.2 times of that under traditional sand spraying.When the amount of sand was 5 g/min,the adhesion coefficient of SiO2 particles by 90 kV electrostatic spraying was 0.28,which was c
24、lose to 0.3 of traditional sand spraying,and the wheel-rail damage was only 75%and 65%of that under traditional sand spraying.The damage to wheel-rail increased by direct spraying SiO2 particles was 66%and 57%of that under traditional sand spraying,but its adhesion coefficient was lower than 0.2.Ele
25、ctrostatic spraying technology can effectively improve the utilization rate of SiO2 particles on the rail surface and enhance the adsorption of particles on the rail surface.The adhesion coefficient of electrostatic spraying SiO2 particles is similar to that under traditional sanding,and the wheel-r
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 钢轨 静电 喷涂 SiO_2 颗粒 行为 利用率 研究 黄启芮
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【自信****多点】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【自信****多点】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。