MESC SPE 76∕212 February 2020 ALLOY AND STAINLESS STEEL FORGINGS(AMENDMENTS∕SUPPLEMENTS TO ASTM A182).pdf
《MESC SPE 76∕212 February 2020 ALLOY AND STAINLESS STEEL FORGINGS(AMENDMENTS∕SUPPLEMENTS TO ASTM A182).pdf》由会员分享,可在线阅读,更多相关《MESC SPE 76∕212 February 2020 ALLOY AND STAINLESS STEEL FORGINGS(AMENDMENTS∕SUPPLEMENTS TO ASTM A182).pdf(13页珍藏版)》请在咨信网上搜索。
1、TECHNICAL SPECIFICATION ALLOY AND STAINLESS STEEL FORGINGS (AMENDMENTS/SUPPLEMENTS TO ASTM A182) MESC SPE 76/212 February 2020 MESC SPECIFICATION DOCUMENT This document is restricted. Neither the whole nor any part of this document may be disclosed to any third party without the prior written consen
2、t of Shell Global Solutions International B.V., The Netherlands. The copyright of this document is vested in this company. All rights reserved. Neither the whole nor any part of this document may be reproduced, stored in any retrieval system or transmitted in any form or by any means (electronic, me
3、chanical, reprographic, recording or otherwise) without the prior written consent of the copyright owner. MESC SPE 76/212 February 2020 Page 2 PREFACE MESC (Materials and Equipment Standards and Code) SPE documents reflect the views, at the time of publication, of: Shell Global Solutions Internation
4、al B.V. (Shell GSI) and/or Shell International Exploration and Production B.V. (SIEP) and/or other Shell Service Companies. They are based on the experience acquired during their involvement with the design, construction, operation and maintenance of processing units and facilities, and they are sup
5、plemented with the experience of Shell Operating Units. Where appropriate they are based on, or reference is made to, international, regional, national and industry standards. The objective is to set the recommended standard for good design and engineering practice applied by Shell companies operati
6、ng an oil refinery, gas handling installation, chemical plant, oil and gas production facility, or any other such facility, and thereby to achieve maximum technical and economic benefit from standardization. The information set forth in these publications is provided to Shell companies for their con
7、sideration and decision to implement. This is of particular importance where MESC SPEs may not cover every requirement or diversity of condition at each locality. The system of MESC SPEs is expected to be sufficiently flexible to allow individual Operating Units to adapt the information set forth in
8、 MESC SPEs to their own environment and requirements. When Contractors or Manufacturers/Suppliers use MESC SPEs they shall be solely responsible for the quality of work and the attainment of the required design and engineering standards. In particular, for those requirements not specifically covered
9、, the Principal will expect them to follow those practices, which will achieve the same level of integrity as reflected in the MESC SPEs. If in doubt, the Contractor or Manufacturer/Supplier shall, without detracting from his own responsibility, consult the Principal or its technical advisor. The ri
10、ght to use MESC SPEs is granted by Shell GSI, in most cases under Service Agreements primarily with Shell companies and other companies receiving technical advice and services from Shell GSI or another Shell Service Company. Consequently, three categories of users of MESC SPEs can be distinguished:
11、1) Operating Units having a Service Agreement with Shell GSI or other Shell Service Company. The use of MESC SPEs by these Operating Units is subject in all respects to the terms and conditions of the relevant Service Agreement. 2) Other parties who are authorized to use MESC SPEs subject to appropr
12、iate contractual arrangements (whether as part of a Service Agreement or otherwise). 3) Contractors/subcontractors and Manufacturers/Suppliers under a contract with users referred to under 1) or 2) which requires that tenders for projects, materials supplied or - generally - work performed on behalf
13、 of the said users comply with the relevant standards. Subject to any particular terms and conditions as may be set forth in specific agreements with users, Shell GSI disclaims any liability of whatsoever nature for any damage (including injury or death) suffered by any company or person whomsoever
14、as a result of or in connection with the use, application or implementation of any MESC SPE, combination of MESC SPEs or any part thereof, even if it is wholly or partly caused by negligence on the part of Shell GSI or other Shell Service Company. The benefit of this disclaimer shall inure in all re
15、spects to Shell GSI and/or any Shell Service Company, or companies affiliated to these companies, that may issue MESC SPEs or require the use of MESC SPEs. Without prejudice to any specific terms in respect of confidentiality under relevant contractual arrangements, MESC SPEs shall not, without the
16、prior written consent of Shell GSI, be disclosed by users to any company or person whomsoever and the MESC SPEs shall be used exclusively for the purpose for which they have been provided to the user. They shall be returned after use, including any copies, which shall only be made by users with the
17、express prior written consent of Shell GSI. The copyright of MESC SPEs vests in Shell GSI. Users shall arrange for MESC SPEs to be held in safe custody and Shell GSI may at any time require information satisfactory to them in order to ascertain how users implement this requirement. All administrativ
18、e queries should be directed to the MESC SPE Administrator in Shell GSI. MESC SPE 76/212 February 2020 Page 3 TABLE OF CONTENTS PART I INTRODUCTION . 4 1.1 SCOPE . 4 1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS . 4 1.3 DEFINITIONS . 4 1.4 CHANGES SINCE PREVIOUS EDITION . 5 1.5 COMMEN
19、TS ON THIS MESC SPE . 5 PART II AMENDMENTS/SUPPLEMENTS TO ASTM A182/A182M19a . 6 PART III REFERENCES . 12 MESC SPE 76/212 February 2020 Page 4 PART I INTRODUCTION 1.1 SCOPE This MESC SPE specifies requirements for alloy and stainless steel forgings. This specification shall apply in addition to the
20、applicable MESC Buying Description, purchase order or requisition sheet. This specification only applies to alloy steel forgings to ASTM A182, F5 (5Cr-0.5Mo), F9 (9Cr-1Mo), F11 Class 2 (1.25Cr-0.5Mo) and F22 Class 3 (2.25Cr-1Mo), and stainless steel forgings to ASTM A182, Grades F304, F304H, F304L,
21、F316, F317L,F321, F321H, F347, F44, F50-F55, F57-F61, F62 and F65-F67. This specification is written as amendments and supplements to ASTM A182/A182M19a, which are covered in Part II of this MESC SPE. The clause numbering of ASTM A182/A182M19a has been retained and any amendments are identified as A
22、dd, Modify to read or Delete. Any clauses of ASTM A182/A182M19a that are not amended or supplemented by this MESC SPE, shall apply as written. This MESC SPE is also written as amendments and supplements to IOGP SPEC S-563 2018. Requirements indicated with blue bold italics underline and red bold ita
23、lics underline font are covered by IOGP SPEC S-563. 1.2 DISTRIBUTION, INTENDED USE AND REGULATORY CONSIDERATIONS Unless otherwise authorised by Shell GSI, the distribution of this MESC SPE is confined to Shell companies and, where necessary, to Contractors and Manufacturers/Suppliers nominated by th
24、em. This MESC SPE is intended for use in oil refineries, chemical plants, gas plants, exploration and production facilities and, where applicable, supply/distribution installations. If national and/or local regulations exist in which some of the requirements may be more stringent than in this MESC S
25、PE the Contractor shall determine by careful scrutiny which of the requirements are the more stringent and which combination of requirements will be acceptable with regards to safety, environmental, economic and legal aspects. In all cases the Contractor shall inform the Principal of any deviation f
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- MESC SPE 76212 February 2020 ALLOY AND STAINLESS STEEL FORGINGSAMENDMENTSSUPPLEMENTS TO ASTM A18
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【li****ok】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【li****ok】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。
链接地址:https://www.zixin.com.cn/doc/75205.html