学术讨论—USP40-1225--药典的验证中英文对照.doc
《学术讨论—USP40-1225--药典的验证中英文对照.doc》由会员分享,可在线阅读,更多相关《学术讨论—USP40-1225--药典的验证中英文对照.doc(14页珍藏版)》请在咨信网上搜索。
1、VALIDATION OF COMPENDIAL PROCEDURES药典方法的验证Test procedures for assessment of the quality levels of pharmaceutical articles are subject to various requirements. According to Section 501 of the Federal Food, Drug, and Cosmetic Act, assays and specifications in monographs of the United States Pharmacope
2、ia and the National Formulary constitute legal standards. The Current Good Manufacturing Practice regulations 21 CFR 211.194(a) require that test methods, which are used for assessing compliance of pharmaceutical articles with established specifications, must meet proper standards of accuracy and re
3、liability. Also, according to these regulations 21 CFR 211.194(a)(2), users of analytical methods described inUSPNFare not required to validate the accuracy and reliability of these methods, but merely verify their suitability under actual conditions of use. Recognizing the legal status ofUSP andNFs
4、tandards, it is essential, therefore, that proposals for adoption of new or revised compendial analytical procedures be supported by sufficient laboratory data to document their validity.用于评估药品质量的检验方法需要满足不同的要求。根据联邦食品,药品,和化装品法案501章,美国药典和国家处方专题论文里的试验和标准构成了法律标准。CGMP法规21 CFR 211.194(a)要求:用于评估药品满足已建立的标准的
5、检验方法必须满足准确、可靠、适当的标准。此外,根据法规21 CFR 211.194(a)(2),USP-NF中表达的分析方法的使用者不需要验证这些方法的准确度和可信度,仅仅需要确认在实际使用条件下的适用性。考虑到USP和NF的法律地位,采用新的或修改后的药典分析方法的建议,并且这个建议是由充分的实验室数据支持以证明其有效,这是十分必要的。The text of this information chapter harmonizes, to the extent possible, with the Tripartite International Conference on Harmoniza
6、tion (ICH) documentsValidation of Analytical Proceduresand theMethodologyextension text, which are concerned with analytical procedures included as part of registration applications submitted within the EC, Japan, and the USA.这一章节的内容尽可能地和ICH文献“分析方法的验证和方法学文献与包含在EC,日本和美国递交的注册申请中的分析方法相关协调一致。SUBMISSIONS
7、 TO THE COMPENDIA递交至药典Submissions to the compendia for new or revised analytical procedures should contain sufficient information to enable members of the USP Council of Experts and its Expert Committees to evaluate the relative merit of proposed procedures. In most cases, evaluations involve assess
8、ment of the clarity and completeness of the description of the analytical procedures, determination of the need for the procedures, and documentation that they have been appropriately validated. Information may vary depending upon the type of method involved. However, in most cases a submission will
9、 consist of the following sections.将新的或修改后的分析方法递交至药典,应包含足够的资料从而使得USP委员会专家和其专家委员会能够评估拟定方法的价值。绝大多数情况下,评估包括透明度的评估和分析方法表达完整性的评估,确定方法需求,以及专家已经充分验证的文件。涉及方法的类别改变,资料可能也会改变。然而,大局部情况下,递交应包含如下的章节RationaleThis section should identify the need for the procedure and describe the capability of the specific procedu
10、re proposed and why it is preferred over other types of determinations. For revised procedures, a comparison should be provided of limitations of the current compendial procedure and advantages offered by the proposed procedure.根本原理此章节应确定方法的需求和表达拟定的具体的方法的能力以及它优于其它类别测定方法的原因。对于已修改的方法,需比拟当前方法的局限性和拟定方法的
11、优点。Proposed Analytical ProcedureThis section should contain a complete description of the analytical procedure sufficiently detailed to enable persons “skilled in the art to replicate it. The write-up should include all important operational parameters and specific instructions such as preparation o
12、f reagents, performance of system suitability tests, description of blanks used, precautions, and explicit formulas for calculation of test results.拟定的分析方法此章节应包含详细完整的分析方法的表达,使得技术人员能够重现。应包括所有的重要的操作参数和具体的操作,如试剂的制备,系统适应性性能的测试,空白溶液使用的表达,考前须知,和用于计算检测结果的明确的公式。Data ElementsThis section should provide thoro
13、ugh and complete documentation of the validation of the analytical procedure. It should include summaries of experimental data and calculations substantiating each of the applicable analytical performance characteristics. These characteristics are described in the following section.资料组成此章节应对分析方法的验证提
14、供周密的和完整的文件。需要包括对于证明每一个实用功能特性的实验数据和计算的概况、总结。这些特征在下面章节中表达。VALIDATION验证Validation of an analytical procedure is the process by which it is established, by laboratory studies, that the performance characteristics of the procedure meet the requirements for the intended analytical applications. Typical an
15、alytical performance characteristics that should be considered in the validation of the types of procedures described in this document are listed inTable 1. Because opinions may differ with respect to terminology and use, each of the performance characteristics is defined in the next section of this
16、 chapter, along with a delineation of a typical method or methods by which it may be measured.分析方法的验证是一个过程:通过实验室的研究确立了方法的性能参数可以满足预期的分析应用的要求。本文件表达的几种方法的验证需要考虑的典型的分析性能参数列在表1中。因为对术语和使用的观点可能会有所不同,所以每个性能参数在此章节的下局部给出定义,以及典型方法或能够测量的方法的描述。Thedefinitionsrefer to “testresults.Thedescriptionoftheanalytical pro
17、cedure shoulddefinewhatthetestresultsfortheprocedureare. As notedinISO5725-1and3534-1,atestresultis“thevalue of acharacteristicobtainedbycarryingoutaspecifiedtest method. The test methodshouldspecifythatoneor anumberofindividual measurementsbemade, and their average,oranotherappropriatefunction(such
18、asthemedianorthe standarddeviation), bereportedasthetestresult.It may alsorequirestandardcorrectionstobeapplied, suchascorrection of gas volumestostandardtemperatureandpressure. Thus,atestresultcan be a resultcalculatedfromseveralobservedvalues. Inthesimplecase, the test result isthe observedvalueit
19、self.Atestresultalsocanbe,butneed not be, the final, reportablevaluethatwouldbecompare totheacceptance criteria of a specification. Validationof physicalpropertymethodsmayinvolve the assessment of the chemometricmodels.However,thetypicalanalytical characteristicsusedinmethodvalidationcanbeappliedtot
20、he methods derived fromtheuseofthechemometricmodels.这些定义指的是“测试结果。“分析过程的描述应该定义这个过程的测试结果。 正如在ISO 5725-1和3534-4中所指出的,测试结果是“通过执行指定的测试方法获得的特征值。 测试方法应该指定一个或多个单独的度量,以及它们的平均值,或者其他适当的函数(如中值或标准差),作为测试结果。它还可能需要进行标准的校正,例如将气体体积调整到标准的温度和压力。因此,一个测试结果可以是由几个测定值计算出来的结果。在简单的情况下,测试结果是测定值本身。测试结果也可以是,但不需要是,最终的,可报告的值,此值可用
21、于比拟一个标准的接受标准。物理属性方法的验证可能涉及到化学计量模型的评估。然而,用于方法验证中的典型的分析可以应用于使用来源于化学计量模型的那些方法。Table 1. Typical Analytical Characteristics Used in Method Validation表1 方法验证中使用的典型的分析特征Accuracy准确度Precision精密度Specificity专属性Detection Limit检测限Quantitation Limit定量限Linearity线性Range范围Robustness耐用性Theeffectsofprocessingcondition
22、sandpotentialforsegregationofmaterialsshouldbeconsideredwhenobtaining a representative sampleto be used for validationof procedures. 当获得代表性样品用于验证程序时,应考虑处理条件和材料隔离的影响。 In the case of compendial procedures, revalidation may be necessary in the following cases: a submission to the USP of a revised analy
23、tical procedure; or the use of an established general procedure with a new product or raw material (see below inData Elements Required for Validation).如果是药典方法,下面的一些情况下有必要进行再验证:将修改的分析方法递交给USP;或者将拟定的关于新产品或原辅料总的分析方法的使用见如下验证需要的资料组成The ICH documents give guidance on the necessity for revalidation in the
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- 精品 医学 专题 USP40 1225 药典 验证 中英文 对照
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【Fis****915】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【Fis****915】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。