NI 用于InstrumentStudio手册的电子电源验证插件.pdf
《NI 用于InstrumentStudio手册的电子电源验证插件.pdf》由会员分享,可在线阅读,更多相关《NI 用于InstrumentStudio手册的电子电源验证插件.pdf(15页珍藏版)》请在咨信网上搜索。
1、Electronics Power Validation Add-On for Instrumentstudio2023-03-01Electronics Power Validation Add-On for InstrumentStudioContentsElectronics Power Validation Add-On for InstrumentStudio Manual.3Launching the Electronics Power Validation Add-On from InstrumentStudio.3Large Panel Overview.4Taking a M
2、easurement.5Logging Data.6Saving a Configured Measurement.7Loading a Configured Measurement.7Pin Maps.7Creating a New Pin Map.8Editing a Pin Map.8Importing and Exporting Configurations as MS Excel Files.9Defining an Electronics Power Validation Add-On Project in a Microsoft ExcelSpreadsheet.9Channel
3、 Mapping Worksheet.10Current Worksheet.11Voltage-Voltage Worksheet.12Source-Measurement Worksheet.13Formula Worksheet.14/Electronics Power Validation Add-On for InstrumentstudioEectronics Power VaHdation Add-On for Instrumentstudio ManuaThe Electronics Power validation Add-On for Instrumentstudio he
4、lps you acquire,visualize,and analyze power consumption and measurement data from PXI instruments.This manual contains only information about the Electronics Power validation Add-On.Refer to the InstrumentStudio Manual for information about navigating,configuring,and using InstrumentStudio.2022-2023
5、 National Instruments Corporation.All rights reserved.Refer to the _Legal Information directory for information about Nl copyright,patents,trademarks,warranties,product warnings,and export compliance.Launching the Electronics Power Validation Add-On from InstrumentStudioComplete the following steps
6、to open the Electronics Power validation Add-On from InstrumentStudio.1.Launch InstrumentStudio.|Note InstrumentStudio version 2022 Q4 or later is required.2.Click Manual Layout on the InstrumentStudio home screen to open the Edit Layout dialog box.3.Find Power Validation within the Nl Electronics P
7、ower validation dialog box.4.Select Create large panel from the drop-down menu for the Power Validation Add-On.National InstrumentsElectronics Power Validation Add-On for Instrumentstudio5.Click OK.After you click OK,Instrumentstudio launches the Electronics Power validation Add-On home screen/large
8、 panel.From this home screen,you can select your connected device from the hardware list and configure any channels before starting the acquisition.Large Panel OverviewThe large panel displays connected devices,configured channels,measurement parameters,and acquisitions.Use this panel to configure m
9、easurements,view applications,capture data,view data,and log data for voltage,current,and power measurements.The large panel includes the following options.Run:Starts or stops an acquisition.Mode:Sets the acquisition to be either continuous or finite.For finite acquisitions,specify time the Test Tim
10、e in seconds.Add Channel:Clicking Add Channel configures terminals or pins at which you can measure signals.Channels also encapsulate channel-specific information such as the voltage range that formats the data.Note To duplicate one or more added channels,including their configuration,right click th
11、e channel or channels to be duplicated in the large panel,and use Copy and Paste.To select multiple channels,hold the key and then click on any channels you want to copy and paste.Start/Stop Log:Begins logging or recording data.Search:Lists the compatible devices detected by the Electronics Power Va
12、lidation Add-On.Trigger:Lists the actions that cause Electronics Power validation Add-On to mark or begin an acquisition on a specified channel.You can specify the type of trigger and whether the trigger occurs if the Slope is rising or falling and the Level at which a trigger will occur.4 Electroni
13、cs Power Validation Add-On for Instrumentstudio Dynamics Graphs:Displays channel-specific waveform data such as the mean,minimum,and maximum waveform values.Instrument view(n):Displays the terminal connections(pinouts)for any connected device.List view(目):Shows the connections as a list for any conn
14、ected device.Related tasks:Taking a Measurement Logging DataTaking a MeasurementBefore you begin this procedure,launch the Electronics Power Validation Add-On and open your project.Complete the following steps to take a measurement.1.Click the device tab for any connected DAQ or SMU devices.Note For
15、 DAQ devices,click Add Channel to configure and include additional channels in your measurement.2.Configure each channel by doing one of the following:From the instrument view,double click a channel row or click the gear icon(a).In the pop-up window,select if the channel will measure voltage or curr
16、ent,specify the range,and for current measurements,specify a shunt resistor value.From the list view,click the channel to be configured(for instance,AI0+).In the pop-up window,select if the channel will measure voltage or current,specify the range,and for current measurements,specify a shunt resisto
17、r value.3.Use Mode to specify whether the measurement will be continuous or finite.If it is finite,specify the Test Time in seconds.4.For DAQ devices,select the Trigger to use and the Sampling rate.National InstrumentsElectronics Power Validation Add-On for Instrumentstudio5.For devices that support
18、 offset adjustments,specify either Auto Zero or Chopping values.Auto Zero uses sampling to adjust the offset whereas Chopping uses modulation and demodulation.Chopping and Auto Zero cannot be used together.6.Click Run/Stop to start the acquisition.Your acquisition begins.You can view the acquisition
19、 in progress by clicking the Dynamics Graphs tab and then selecting the channels to view.|Note Click Save to store your 叩plication to be reloaded again later.Related concepts:Large Panel OverviewLogging DataBefore you begin this procedure,launch the Electronics Power validation Add-On to open your p
20、roject in the large panel,and configure any voltage,current,and power measurements for any connected channels.Complete the following steps to capture and record data.1.Configure logging by clicking the gear icon(fi).This opens the Logging specification window.2.In the Logging specification window,se
21、lect an output path,specify if you want files segmented by time or file size,and configure CSV file formatting.3.Click Okay to close the Logging specification window and return to the large panel.4.Click Run/Stop to start acquiring data.5.For finite measurements,specify the acquisition duration by s
22、etting the Mode to Finite and entering the Test Time in seconds.6.Choose one of the following:To manually control a recording,click Start Log to begin capturing data.6 Electronics Power Validation Add-On for Instrumentstudio To automatically start a recoding,click Run.7.For continuous measurements,c
23、lick Run/Stop to end recording data.For finite measurements,the recording ends when the capture duration is completed.Related concepts:Large Panel OverviewSaving a Configured MeasurementTo save a configuration,do the following.Select File Save or File Save all.The configuration file is saved as a.sf
24、p file included in the project(.inststudioproj file).Note When closing Instrumentstudio,the Electronics Power validation Add-On also prompts you to save the configuration.Loading a Configured MeasurementTo reuse a saved configuration,do the following.1.Click Load to add a saved configuration.2.Navig
25、ate to the location where the configuration is saved,and double click the instudioproj file.The saved sampling rate,voltage range,trigger,signal connections,and channels are displayed on the large panel.Note When opening Instrumentstudio,the last project saved is automatically re-opened.Pin MapsPin
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NI 用于InstrumentStudio手册的电子电源验证插件 用于 InstrumentStudio 手册 电子 电源 验证 插件
1、咨信平台为文档C2C交易模式,即用户上传的文档直接被用户下载,收益归上传人(含作者)所有;本站仅是提供信息存储空间和展示预览,仅对用户上传内容的表现方式做保护处理,对上载内容不做任何修改或编辑。所展示的作品文档包括内容和图片全部来源于网络用户和作者上传投稿,我们不确定上传用户享有完全著作权,根据《信息网络传播权保护条例》,如果侵犯了您的版权、权益或隐私,请联系我们,核实后会尽快下架及时删除,并可随时和客服了解处理情况,尊重保护知识产权我们共同努力。
2、文档的总页数、文档格式和文档大小以系统显示为准(内容中显示的页数不一定正确),网站客服只以系统显示的页数、文件格式、文档大小作为仲裁依据,平台无法对文档的真实性、完整性、权威性、准确性、专业性及其观点立场做任何保证或承诺,下载前须认真查看,确认无误后再购买,务必慎重购买;若有违法违纪将进行移交司法处理,若涉侵权平台将进行基本处罚并下架。
3、本站所有内容均由用户上传,付费前请自行鉴别,如您付费,意味着您已接受本站规则且自行承担风险,本站不进行额外附加服务,虚拟产品一经售出概不退款(未进行购买下载可退充值款),文档一经付费(服务费)、不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
4、如你看到网页展示的文档有www.zixin.com.cn水印,是因预览和防盗链等技术需要对页面进行转换压缩成图而已,我们并不对上传的文档进行任何编辑或修改,文档下载后都不会有水印标识(原文档上传前个别存留的除外),下载后原文更清晰;试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓;PPT和DOC文档可被视为“模板”,允许上传人保留章节、目录结构的情况下删减部份的内容;PDF文档不管是原文档转换或图片扫描而得,本站不作要求视为允许,下载前自行私信或留言给上传者【曲****】。
5、本文档所展示的图片、画像、字体、音乐的版权可能需版权方额外授权,请谨慎使用;网站提供的党政主题相关内容(国旗、国徽、党徽--等)目的在于配合国家政策宣传,仅限个人学习分享使用,禁止用于任何广告和商用目的。
6、文档遇到问题,请及时私信或留言给本站上传会员【曲****】,需本站解决可联系【 微信客服】、【 QQ客服】,若有其他问题请点击或扫码反馈【 服务填表】;文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“【 版权申诉】”(推荐),意见反馈和侵权处理邮箱:1219186828@qq.com;也可以拔打客服电话:4008-655-100;投诉/维权电话:4009-655-100。