土木工程概论(英文版)Chapter-2-Materials-for-Civil-Engineeri.ppt

土木工程概论,Introduction to Civil Engineering,第二章土木工程材料,Chapter 2,Materials for Civil Engineering,Materials for Civil Engineering,What is Materials of Civil Engineering?,It covers the development,processing,evaluation,applications,and performance of construction materials in civil engineering.,Wide varieties of materials are used for making engineering structures and buildings.It is necessary for an engineer to have a basic knowledge of these materials which are available either from natural resource or manufactured.,Stones:,Stones are used in Civil Engineering constructions in different forms.,Stone blocks irregular in size called rubbles are used for building walls.,Smaller irregular stones are used for constructing the base of floors and roads.,Stones broken into smaller pieces are called aggregates.,Stones required in these ways are obtained from rocks.,Materials for Civil Engineering,Bricks:,Common building bricks are rectangular solids,made of burnt clay.,The earth used for the manufacture of bricks should contain 2030%of clay,2540%of sand and 2535%of silt.,The manufacture of bricks involves the following four operations:,Preparation of clay,Moulding,Dry,Burning,Materials for Civil Engineering,Cements:,Even in 100 BC,Roman builders used a special volcanic ash for cementing stones.,When this ash was mixed with limestone,burnt and combined with water,it became a very strong cement.,The builders found this cement would harden with water.,Hence,it was called Hydraulic cement.,Materials for Civil Engineering,Uses of cements:,To make cement mortar and cement concrete,Wide varieties of purposes staring from ordinary foundation to roofs of multistory skyscrapers,Sulphate,resisiting,cement is used to protect the foundations and other components in contact with the earth against the chemical action of,sulphate,in the soil,Rapid hardening cement and early strength cement have been used in works which need early strength gain like chimneys and underwater concreting,White and colored cements are used for making ornamental plastering and floor finish,Materials for Civil Engineering,Concrete:,When stone or gravel,sand,cement and water are mixed together,they form an easily workable plastic mixture which can be,moulded,and cast into desired shapes or structures.,This cement and water in the plastic mixture undergo a chemical combination in a few hours after the mixing results in a solidification and gradual hardening.,This mixture is called concrete.,Materials for Civil Engineering,Concrete:,Concrete is a very strong material when it is placed in compression.It is,however,extremely weak in tension.It is for this reason that we use reinforcement in concrete structures.The reinforcement,which is usually steel,takes up the slack for the weakness of the concrete in tension.,Materials for Civil Engineering,Concrete:,There are many ways to test the strength of a batch of concrete.The tests used can be categorized as destructive and nondestructive tests.We will perform both types of tests in this class.,Materials for Civil Engineering,Concrete:,These cylinders are cured for 28 days and tested by compression until they are crushed.This will give the contractor or the engineer the compressive strength for that batch of concrete.He or she can then compare that value to the design value used to make sure that the structure was constructed properly.,Materials for Civil Engineering,Concrete tests:,Each group will perform two tests on a concrete cylinder.The first test will be the Schmidt hammer test.Each person in the group will take a turn using the Schmidt hammer and the results of the group members will be averaged.Each group will then take their cylinder into the structures lab where it will be tested to crushing in a compression testing machine.,Materials for Civil Engineering,Concrete strength:,Concrete and steel are the most widely used materials in engineering design.,Concrete is very important material for the civil engineer designing because steel is not readily available and can be very expensive to bring to the site.,Materials for Civil Engineering,Concrete strength:,As you walk around Weil Hall(the building you are in now)you will notice that the beams and columns are made of concrete.,The new South End zone for the University of Floridas Football Stadium and the new addition to the commuter parking garage were constructed using concrete.These are just a few examples.,Materials for Civil Engineering,Concrete strength:,Concrete is composed of four ingredients:,cement,sand,aggregate(stones,gravel,etc.),and water,.The strength and other properties of concrete are dependent on how these four ingredients are proportioned and mixed.The most common type of cement is Portland.,Materials for Civil Engineering,Concrete strength:,Unlike steel,concrete is adequate in strength in only one direction.Concrete is very good in compression but useless in tension.,Engineering design is based on concretes,compressive strength,.Compressive strength,fc,refers to what concrete is capable of resisting from loads when they are pushing on the concrete(compression).,Materials for Civil Engineering,Concrete strength:,Compressive strengths for concrete are usually in the range of 3 000 to 5 000,psi,(pounds per square inch).To correct for the lack of tension strength in concrete,high tensile strength steel is placed in the tension side of concrete.The steel used for reinforcement usually consists of round steel bars often called,rebars,.When this combination occurs it is called reinforced concrete.,Materials for Civil Engineering,Concrete strength:,When Civil Engineers design,they obviously need to know the strength of the material that they are using.By knowing the strength of the material that is being used and the loads(forces i.e.people,cars,furniture)that will be acting on the particular member(beam,column,arch,etc.)the engineer can pick the correct dimensions for the design.,Materials for Civil Engineering,Concrete strength:,The American Concrete Institutes Code specifies that a pair of cylinders shall be tested for each 150 yd,3,of concrete or for each 5 000 ft,2,of surface area actually placed.This is a quality control measure.,Materials for Civil Engineering,Concrete strength:,The other test that we will conduct in the lab today is called the Schmidt(or Swiss)Hammer Test.,This test gives an estimate of the concretes compressive strength.This test is performed in situations where the concrete has already been poured and a cylinder test is not possible.,Materials for Civil Engineering,Concrete strength:,If a structural engineer wanted to check a beam for its concrete strength 6 months after the building had been constructed the engineer might use this test.What are possible sources of error between the two tests and within the tests themselves?,Materials for Civil Engineering,Steel:,We will perform two tests which can be related to steel.These tests will be a tension test,which can be used to measure the material properties of a steel(or really any material,for that matter),and a beam bending test,which can be used to measure the material properties of a specimen and the effectiveness of the orientation of the beam.,Materials for Civil Engineering,Steel:,We will be using small aluminum beam specimens to simulate steel beams.The mechanics are the same only aluminum is more flexible than steel,so it is easier to see deflections with aluminum.,Materials for Civil Engineering,Reinforced Concrete:,Concrete has a great compressive strength.,However,its tensile strength is very low.,In reinforced concrete,steel and concrete are combined to take advantage of high compressive strength of concrete and high tensile strength of steel.,The location of steel within the concrete is important.The tensile area needs steel reinforcement.,Materials for Civil Engineering,Reinforced Concrete:,The location of steel within the concrete is important.The tensile area needs steel reinforcement.,Materials for Civil Engineering,Basci Civil and Mechanical Engineering,Reinforcment concrete beam,Timber:,Woods are generally classified for construction as hard wood,medium hard wood,and softwood classes.,Wood is graded according to natural defects present in the timber,like knots and sloping grains.,Materials for Civil Engineering,What are the forms in which stones are used in Civil Engineering?,What are the qualities of good building stones?,What are the dimensions of ordinary bricks?,What are the general uses of bricks?,What is the constituent of concrete?,Explain in brief the manufacture of cements.,What are the uses of cements?,Explain the influence of water-cement ratio on the properties of concrete.,What is the need for providing reinforcements to a concrete beam?,What are the advantages of steel as a construction material?,Review Questions,Materials for Civil Engineering,