友通CB50-V3主板说明书.pdf

CB50-V3Rev.A+System Board Users Manual38000849CopyrightThis publication contains information that is protected by copyright.No part of it may be reproduced in any form or by any means or used to make any transformation/adaptation without the prior wntten permission from the copyright holders.This publication is provided for informational purposes only The manufacturer makes no representations or warranties with respect to the contents or use of this manual and specifically disclaims any express or implied warranties of merchantability or fitness for any particular purpose.The user will assume the entire risk of the use or the results of the use of this document.Further;the manufacturer reserves the right to revise this publication and make changes to its contents at any time,without obligation to notify any person or entity of such revisions or changes.All Rights Reserved.1998TrademarksMicrosoft MS-DOS,Windows,Windows 95 and Windows 98 are registered trademarks of Microsoft Corporation.Intel and Celeron are registered trademarks of Intel Corporation.Award is a registered trademark of Award Software,Inc.Other trademarks and registered trademarks of products appearing in this manual are the properties of their respective holders.Caution:Danger of explosion if battery incorrectly replaced.Replace only with the same or equivalent type recommended by the manufacturerDispose of used batteries according to the battery manufacturers instructions.FCC and DOC Statement on Class BThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC rules.These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation.This equipment generates,uses and can radiate radio frequency energy and,if not installed and used in accordance with the instruction manual,may cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:,Reorient or relocate the receiving antenna.,Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.,Consult the dealer or an experienced radio TV technician for help.Notice:I.The changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.2.Shielded interface cables must be used in order to comply with the emission limits.Table of ContentsChapter I-IntroductionI.I Features and Specifications.61.2 Package Checklist.I 0Chapter 2-Hardware Installation2.1 System Board Layout.I I22 System Memory.122.3 DIP Switch Settings for Processors.I 22.4 Jumper Settings for the CPUs Front Side Bus.I 32.5 Jumper Settings for Clearing CMOS Data.I 42.6 Jumper Settings for Wake-On-Keyboard/Wake-On-MouseI 52.7 Connecting the Ribbon Cables and Wires of the Ports and Connectors.I 6Chapter 3-Award BIOS Setup Utility3.1 The Basic Input/Output System.283.1.1 Standard CMOS Setup.283.1.2 BIOS Features Setup.3 I3.1.3 Chipset Features Setup.343.1.4 Power Management Setup.363.1.5 PNP/PCI Configuration.403.1.6 Load Fail-Safe Settings.423.1.7 Load Optimal Settings.423.1.8 Integrated Peripherals.423.1.9 Supervisor Password.473.1.10 User Password.473.1.1 I IDE HDD Auto Detection.483.1.12 Save&Exit Setup.493.1.13 Exit Without Saving.49Chapter 4-Supported Softwares4.1 Desl72OmA(minimum).Wake-On-Keyboard/Wake-On-Mouse(ATX power supply only)This function allows you to use the keyboard or mouse to poweFon the system.Refer to“Jumper Settings for Wake-On-Keyboard/Wake-On-Mouse in Chapter 2 and HKeyboard/Mouse Power On in the Integrated Peripherals setup of the Award BIOS in Chapter 3 for more information.Important:The power button will not function once a keyboard password has been set in the“KB Power On Password”field of the Integrated Peripherals setup.You must type the correct password to poweeon the system.,The 5VSB power source of your power supply must support 720mA(minimum).ACPI(ATX power supply only)The system board is designed to meet the ACPI(Advanced Configuration and Power Interface)specification.ACPI has energy saving features that enables PCs to implement Power Management and Plug-and-Play with operating systems that support OS Direct Power Management.Virus ProtectionMost viruses today destroy data stored in hard drives.The system board is designed to protect the boot sector and partition table of your hard disk drive.91Introduction1.2 Package ChecklistThe system board package contains the following items:0 The system board0 A users manual0 Serial,mouse and printer port cablesOption I:-One card-edge bracket with a 9-pin and 25-pin serial port cables-One card-edge bracket with a 25-pin printer port cable and a PS/2 mouse port cableOption 2:-One card-edge bracket with two 9-pin serial port cables and a PS/2 mouse port cable-One 25-pin printer port cable for chassis mounting0 One 40-pin IDE hard disk cable0 One 34-pin floppy disk drive cable0 One CD One card-edge bracket with two USB ports(optional)If any of these items are missing or damaged,please contact your dealer or sales representative for assistance.10Chapter 2-Hardware Installation2.1 System Board LayoutI IHardware Installation2.3 DIP Switch Settings for Processors(For Factory Use Only)The table on the next page shows the supported processors and their corresponding DIP switch settings(SWI).There are 4 switches on SWI.The black rectangle in the diagram denotes the part that is protruding,the“adjustable switch.Make sure SWI is set correctly before applying power;otherwise you will not be able to power-on the system.Black rectangle denotes the part that is protruding,the adjustable switchIn the example above:Switch I:OffSwitch 2:OnSwitch 3:OffSwitch 4:On12Hardware InstallationProcessorFrequency RatioSWIProcessorFrequency RatioSWI66MHz100MHz66MHz100MHz300MHzFuture processor4.5xSBSBi 1。433MHzFuture processor6.5xBSSBil，乙 1。|333MHzFuture processor5x Z 1 o IFuture processorFuture processor7x|白乙1。1366MHzFuture processor5.5x1BBHI :1。Future processorFuture processor7.5x400MHzFuture processor6xP E Z 1 O|Future processorFuture processor8xIW|上一 1 oNote:I.Intel Celeron PPGA processors support VID(Voltage Identification).The switching voltage regulator on the system board will automatically set the voltage regulator according to the voltage of the processor.2.ybu cannot overclock an Intel Celeron PPGA processor because its frequency ratio has been fixed by the manufacturer.The table above is for fjctory use only.2.4 Jumper Settings for the CPUs Front Side BusJumper JP2CPUs Front Side Bus SelectThe default setting of jumper JP2 is Auto-the system will automatically run according to the FSB of the processor The,IOOMHz,setting(1-2-3 Off)is reserved for future 100MHz FSB processors.Refer to the figure on the next page.Warning:If your system is installed with a 66MHz FSB processor,do notJP2move the jumper cap from its default setting which is pins I and 2 On;otherwise your system will not boot13Hardware InstallationJumper JP2s settings are shown below.O 3I-2 On:Auto(default)2-3 On:66MHz 1-2-3 Off:100MHz2.5 Jumper Settings for Clearing CMOS DataJumper JP6Clear CMOS DataIf,for some reason,the CMOS data becomes corrupted or you forgot the supervisor/user/keyboard password,the system can be reconfigured with the default values stored in the ROM BIOS,Id load the default values,power off your system and unplug the power cord.If you are using an AT power supply,you do not need to unplug the powercord.Set JP6 pins 2 and 3 to On.Wait for a few seconds and set JP6 back to its default setting,pins I and 2 On.bu may now plug the power cord and powenon your system.O 31-2 On:Normal(default)2-3 On:Clear CMOS Data14Hardware Installation2.6 Jumper Settings for Wake-On-Keyboard/Wake-On-Mouse(ATX power supply only)Jumper JPIWake-On-Keyboard/Wake-On-MouseThe system board supports the Wake-On-Keyboard/Wake-On-Mouse function.This function allows you to use the keyboard or mouse to power-on the system.By default,JPI is disabled.7b use this function,set JPI to 2-3 On.HKeyboard/Mouse Power On in the Integrated Peripherals setup of the Award BIOS must be set accordingly.Refer to chapter 3 for details.Warning:I.If JPI was previously enabled with a password set in the“KB Power On Password field,and now you wish to disable the Wake-On-Keyboard(password)function,make sure to set the fKeyboard/Vlouse Power On field to Disabled prior to setting JPI to disabled You will not be able to boot up the system if you fail to do so.2.The power button will not function once a keyboard password has been set in the“KB Power On Password field of the Integrated Peripheinls setup.You must type the correct password to poweaon the system.3.The 5VSB power source of your power supply must support 720mA(minimum).3 2 II。II-2 On:Disable(default)3 2 I2-3 On:Enable15Hardware Installation2.7 Connecting the Ribbon Cables and Wires of the Ports and Connectors2.7.1 Serial PortsThe built-in serial ports are RS-232c asynchronous communication ports with 16C550A-compatible UARTs that can be used with modems,serial printers,remote display terminals,and other serial devices.You can set the serial ports I/O address in the Integrated Peripherals setup of the/Ward BIOS.Connecting the Serial PortsTwo serial port cables mounted on a card-edge bracket are provided with the system board.Connect one serial port cable to connector JP4 for COM I primary serial port and the other serial port cable to connector JP3 for the COM 2 secondary serial port.Make sure the colored stripes on the ribbon cables are aligned with pins I of connectors JP3 and JP4.Mount the card-edge bracket to the system chassis.16Hardware Installation2.7.2 PS/2 Mouse PortThe PS/2 mouse port is a 6-pin connector on the system board.Attach the 6-pin mouse port cable,which is mounted on a card-edge bracket,to connector J2.Make sure the red wire on the PS/2 mouse connector is aligned with pin I of connector J2.Mount the card-edge bracket to the system chassis.The PS/2 mouse port uses IRQ 12.If a mouse is not connected to this port,the system will reserve IRQ 12 for other expansion cards.Warning:Make sure to turn off your computer prior to connecting or disconnecting a mouse.Failure to do so may damage the system boardI23456一 00 0 0 61 2,PinFunction1Mouse Data2Reserved3Ground4+5V5Mouse Clock6Reserved17Hardware Installation2.7.3 Parallel PortThe system board has a standard printer port for interfacing your PC to a parallel printer.It supports SPR ECP and EPP modes.Ydu can set the ports mode in the Integrated Peripherals setup of the Award BIOS.Connecting the Parallel Printer PortAttach the DB-25 printer port cable to connector JP5 on the system board.Make sure the colored stripe on the ribbon cable aligns with pin I of JP5.Use a small nutdriver to mount the cable into a DB-25 cutout in the system chassis.If your printer port cable is attached to a card-edge bracket,connect the cable to connector JP5 on the systemboard and mount the card-edge bracket to the system chassis.2.7.4 Floppy Disk ControllerI.Install the 34-pin header connector into the shrouded floppy disk header(J 10)on the system board.The colored edge of the ribbon should be aligned with pin I of J10.2 Install the other 34-pin header connector(s)into the disk drive(s).Align the colored edge of the daisy chained ribbon cable withpin I of the drive edge connector(s).The end-most connector should be attached to the drive you want to designate as Drive A.18Hardware Installation2.7.5 IDE Hard Disk InterfaceI.If you are connecting two hard drives,install the 40-pin connector of the IDE cable into the primary shrouded IDE header(connector J8).If you are adding a third or fourth IDE device,install the 40-pin connector of the other IDE cable into the secondary shroudedIDE header(connector J7).2 Install the other 40-pin header conn ecto r(s)into the device with the colored edge of the ribbon cable aligned with pin I of the drive edge connector(s).Note:Refer to your disk drive users manual for information about selecting proper drive switch settings.Adding a Second IDE Hard DriveWhen using two IDE drives,one must be set as the master and the other as the slave.Follow the instructions provided by the drive manufacturer for setting the jumpers and/or switches on the drives.Ne recommend that you use Enhanced IDE or ATA-2,ATA-3 and Ultra DMA hard drives be from the same manufacturer In a few cases,drives from two different manufacturers will not function properly when used together The problem lies in the hard drives,not the system board.Important:If you encountered problems while using an AIAPI CD-RO/V drive that is set in Master mode,please set the CD-ROM drive to Slave mode.Some ATAPI CD-RO/Vs may not be recognized and cannot be used if incorrectly set in Master mode.19Hardware Installation2.7.6 USB PortsThe system board is equipped with a header at location JI I on the system board,for external USB ports.USB allows data exchange between your computer and a wide range of simultaneously accessible external Plug and Play peripherals.Vbu must have the proper drivers installed in your operating system to use these ports.Refer to your operating systems manual or documentation.Connecting the USB PortsAs an option,one card-edge bracket mounted with two USB port cables may be provided with the system board.The ends of the cables are attached to a connector Connect the USB cable connector to JI I on the system board.The USB port cables can be inserted only if pin I of the cable(red wire)is aligned with pin I of JI I.Pin 9 of JI I has been removed and the hole in the USB cable connector;which corresponds to pin 9,has been plugged to prevent incorrectly inserting the connector.Mount the card-edge bracket to the system chassis.PinFunctionPinFunction1+5V2+5V3-Data4-Data5+Data6+Data7Ground8Ground9Key10Ground20.Hardware Installation2.7.7 IrDA ConnectorThe system board is equipped with an IrDA connector for wireless connectivity between your computer and peripheral devices.The IRDA(Infrared Data Association)specification supports data transfers of I I5K baud at a distance of I meterConnect your IrDA cable to connector J5 on the system board.Set“UART2 Mode Select in the Integrated Peripherals setup of the Award BIOS to the type of IrDA standard supported by your device.bu must have the proper drivers installed in your operating system to use this connector Refer to your operating system s manual or documentation.PinFunction1IRTX2Ground3IRRX4N.C.5VCC21Hardware Installation2.7.8 CPU Fan ConnectorThe processor must be kept cool